Leave Your Message
what is Complete Installation Procedures for Stationary Ring Seat and Stationary Ring of Type 212 Mechanical Seal (Commonly Used for Glass-Lined Reactors)?
Company News
News Categories
Featured News

what is Complete Installation Procedures for Stationary Ring Seat and Stationary Ring of Type 212 Mechanical Seal (Commonly Used for Glass-Lined Reactors)?

2026-06-01

Complete Installation Procedures for Stationary Ring Seat and Stationary Ring of Type 212 Mechanical Seal (Commonly Used for Glass-Lined Reactors)

mechanical seals in 212.jpg

Type 212 Mechanical Seal Step-by-Step Installation Instructions

Step 1: Prepare the Stationary Ring Seat Assembly

  1. Take out the main stationary ring seat (housing) from the kit.
  2. Inspect the seat for any cracks, burrs, or surface damage.
  3. Clean the seat thoroughly with a lint-free cloth and a suitable solvent (e.g., isopropyl alcohol) to remove oil, dust, or contaminants.

Step 2: Install the Gasket/Backing Ring

  1. Take the metal or PTFE backing ring (part 2).
  2. Align it with the recess on the stationary ring seat.
  3. Ensure the ring sits flat and square without tilting or misalignment.

Step 3: Position the Intermediate Flange

  1. Fit the intermediate flange (part 3) onto the stationary ring seat.
  2. Align the bolt holes with the seat to ensure proper positioning.
  3. Check for any gaps or uneven seating that may cause misalignment later.

Step 4: Install the Stationary Ring

  1. Take the stationary ring (part 4, usually made of silicon carbide or ceramic).
  2. Clean the sealing face with extreme care—do not touch the polished surface with bare hands.
  3. Insert the stationary ring into the housing bore. Ensure the anti-rotation groove aligns with the anti-rotation pin in the seat.
  4. Press it gently into place until it seats against the shoulder of the housing.

Step 5: Secure the Stationary Ring Assembly

  1. Ensure the stationary ring is flush and level in the seat.
  2. Check for any wobble or binding. If it is loose or tilted, remove and re-seat it carefully.
  3. Confirm the ring does not rotate freely (anti-rotation pin engagement).

Step 6: Fit the Secondary Sealing Element

  1. Take the PTFE or rubber O-ring/gasket (part 6).
  2. Apply a thin, compatible lubricant (per manufacturer specifications) to the ring to ease installation.
  3. Fit the ring into the corresponding groove on the stationary ring seat. Ensure it is not twisted, pinched, or damaged.

Step 7: Install the Outer Housing Cover

  1. Place the outer housing cover (part 7) over the assembly.
  2. Align the bolt holes with the stationary ring seat.
  3. Check the fit to ensure no part of the cover touches or damages the stationary ring face.

Step 8: Install the Retaining Flange

  1. Take the retaining flange (part 8).
  2. Align it with the bolt holes on the outer housing cover.
  3. Keep the assembly aligned and square to avoid stress on the stationary ring.

Step 9: Tighten the Fasteners Evenly

  1. Insert the bolts through the flange holes.
  2. Tighten them in a cross-pattern, incrementally (e.g., 1/4 turn each pass) to ensure uniform pressure on the stationary ring.
  3. Do not over-tighten, as this can cause the ring to crack or distort.

Step 10: Final Assembly and Inspection

  1. Verify the stationary ring face is still clean, flat, and undamaged.
  2. Check the assembly for any signs of misalignment or binding.
  3. Confirm all fasteners are secure.
  4. The completed stationary ring seat assembly (part 10) is now ready to be mounted onto the glass-lined reactor flange.

Critical Installation Notes

  1. Cleanliness is Key: The sealing faces must be free of oil, dust, fingerprints, or fibers at all times. Even minor contamination can cause leaks.
  2. Handle the Stationary Ring with Care: The polished sealing face is easily scratched or chipped. Use only lint-free cloths for cleaning.
  3. Uniform Tightening: Always tighten bolts in a cross-pattern to distribute pressure evenly and prevent distortion of the stationary ring.
  4. Alignment Check: After installation, verify the stationary ring face is perpendicular to the shaft centerline (runout ≤ 0.05 mm recommended).
  5. Lubrication: Only use lubricants specified by the manufacturer; avoid using incompatible oils or greases that can degrade the sealing materials.